Free Training
5 Easy Steps to Consistent Great Sound
GET ACCESS

A Quick Guide to Mixing Vocals for Worship

Kade Young
Kade Young
Chief Audio Guru
SHARE
Vocal EQ Cheat Sheet

Mixing vocals is an art.

It's tough to get them right, especially hearing the lead vocal throughout the entire song without things getting to loud.

To help you navigate the troubled waters, here is a short guide for mixing vocals.

First, set gain properly for each vocal.

Good sound starts with gain. Yet, most church sound techs are not quite sure how gain is different from adjusting the volume. If you do not quite understand gain, be sure to check out my post, How to Set the Gain on Your Mixer. You will discover the true purpose of gain along with a step-by-step guide for getting it set right each time.

Cut the lows out of all vocals.

If a vocalist is singing into a mic like they should (distance of an inch or less from microphone to mouth), you will get a nice, full sound. However, if you leave the EQ as is, there will be way too much low frequency noise, which makes it sound muddy and also gets in the way of instruments that belong in that space.

To fix this problem you should first activate the low cut filter (aka 'high pass filter') on every vocal. This gets rid of low frequency pops and unwanted breathing noise by cutting low frequencies that shouldn't be reproduced on a vocal anyways.

On an analog mixer, the high pass filter button is usually located by the gain knob and looks like /100. On a digital mixer (like the Behringer X32), simply activate the low cut filter and set the frequency to around 120Hz.

Although this takes care of most issues, you still may want to clean it up a bit using the low frequency knob if you have an analog mixer, or changing the frequency position of your low cut filter if you have a digital mixer. Simply cut out the lows until you get a nice clean sound that still has plenty of warmth.

Mix background vocals…in the background.

It is common for churches to mix all vocals in the foreground and bury all the instrumentalists. But, there is a better way. Your mix should have layers and contrast. On the top layer is your lead vocal followed by the instruments that create energy: bass and drums. Then your lead instrument which changes from song to song. For example, in a song like Wake, synth is the lead instrument. But in a song like Good Good Father, acoustic guitar is the lead instrument.

Then, simply layer in the background vocals and other instruments where they fit best. Keep in mind, you do not have to audibly hear every single instrument and vocal. But, you should notice a change if the channel is muted.

You might also enjoy: How to Make Lead Vocals Sound Amazing

Don’t forget about compression.

If you do not have compression on vocals, you are in for a bumpy ride! There is simply too much dynamic range in a vocal to let it run free. Compression takes the dynamic range and narrows it down, depending on how much compression is added. Then, you will not have to ride the fader up and down through the whole song as the vocal gets louder and softer.

On the other hand, too much compression can take the life out of a vocal. As a baseline measurement, make sure the vocal isn’t compressed more than 6dB on average. The goal is to narrow the dynamic range, not eliminate it.

To learn more, see: How to Set a Compressor for Vocals

Use reverb and delay, but not too much.

When effects (reverb, delay, etc.) are not used on a vocal, it sounds dry and dead. But, effects can also become a distraction when used too liberally. When in doubt, use a plate reverb to bring life and space to the vocal. Turn it up until you hear it, then bring it down to where it doesn’t stand out.

To help separate a lead vocal from background vocals, try using a plate reverb on the lead and hall reverb on the background vocals. This will put them in two different ‘spaces’ so to speak and add a little interest to the sound.

There really is no set-in-stone way to mix effects, so don’t be afraid to experiment. Different songs will have different applications. For example, there may be a song where you want to hear the trailing delay and another where you want the delay to be buried in the mix. Be creative, but don’t forget to cut the effects if the lead vocal starts talking instead of singing...

Vocal EQ Cheat Sheet

8 Comments

Leave a Reply

Your email address will not be published. Required fields are marked *

8 comments on “A Quick Guide to Mixing Vocals for Worship”

    1. I wish I had came across an info site like this 10yrs ago. I been doing sound longer than that but don't know a lot of the fundamental terminology to discuss it intelligently to further understand what the heck I'm doing.

  1. Kade, great article man. I followed a link on a media tech group and got here. Your info is not wrong but I would like to add something to your idea on BGV's. Don't take out lows on BGV's. As a matter of fact do the polar opposite. LPF them down to 4K. I am sure this is counter intuitive to most everything you have learned over the years but all the BGv information you need will still be there. I exaggerate low freq's on BGV's and try to use them more like a synth PAD. No singer will have a root resonant frequency above 1.72k. There is also another good reason for this technique: vocal timing errors. Transient harmonic frequencies live above 4k. This is where the percussive articulation is perceived. By eliminating or taming those frequencies you begin to take away the perceivable timing issues with vocals not hitting exactly right. You will be amazed at how tightened you over all mix will become. Now if your BGv becomes a lead singer then flip the eq to bypass or better yet use you "B" side of eq (digital consoles) and set your lead eq so that they can pop right out when it's time, and it's easy for FOH mixer to get in and out. Just some food for thought. I have been running FOH for Disney, And WMG artist for nearly 25 years.

    1. Hey John - thanks for the tips! This is definitely a strategy that works well and I have used it before. However, at my church, we generally have 3-4 vocalists on stage and they all lead a song in the service. So, in our situation, we do not use this technique as it would be too much for the volunteer sound tech to keep up with (switch EQ back and forth through the entire service). That being said, if we had more vocalists with less lead vocals, I'd definitely be using the technique you explained.

  2. Thank you so much for all your time and effort in getting this kind of information out to us. Before I 'accidentally' ended up mixing sound at our church, I knew nothing, and when I found out that I am needed on the board now 3 Sundays a month I knew I'd better get with it. I have taken all your tips and applied them over the last several months and things have definitely improved both in house and in our livestream. Anyways, I never thought that you can apply one reverb type to the lead vocal and another to the background vocals. Lately, I've been using panning to separate the voices to get them to stand out in addition to using reverb, but I am going to try your idea with differing reverbs... and I'm excited to see what that does. Its always fun learning new things and applying them!

    1. Awesome, Christy! You'll have to let me know how it goes with the reverb trick.

linkedin facebook pinterest youtube rss twitter instagram facebook-blank rss-blank linkedin-blank pinterest youtube twitter instagram